Build a Backyard Waterfall and Stream

Nature is beautiful. Everything that projects this wonderful serenity of nature is also great. Waterfalls and green growth around are spectacular. Now it is possible for us to build a backyard waterfall and stream in our home. It complements other features and also provides a good place to sit and to forget the whole day’s stress. The water rippling sound as it hits the rocks and water clarity gives us the feeling that we are in the woods having adventure. Now in this article you will read how to build a back yard waterfall stream.

Materials needed-
There are few tools and materials required to complete the project. The tools include a wheelbarrow, spade, level, rubber mallet and utility knife. The required materials include, waterfall pump, horse kit, connections, gravel, clamps and ball valve, cement, PVC primer, EPDM pond liner, saw bits, waterfall foam sealant, sewage basin, lid, field and decorative boulders and an underlayment fabric.

Step by step instructions:

Step 1: A project overview-
The end result of this program is to have a stream that flows into a gravel bed, it stays clean with little maintenance. Gravel will filter the water, which is then collected by the pump at the end of the stream. The pump takes the water to the top again. The stream is gentle sloping with multiple falls as it goes down. There is also a liner and catch basin. The area around the fall needs landscaping to create a serene environment.

Step 2: Location-
As the owner, it is good to study and visualize the best location for the waterfall. It could be behind trees or at the deck. There are a few areas points that you should consider when selecting the location of the waterfall. To start with, it is good to study the soil, if it is hard to dig; a pond above the ground on the stones is advisable. However, if the soil is easy to dig, a shallow pond can be dung below the ground level. A gentle slope is needed to facilitate the flow of water. The waterfall needs a height of 4 to 6 meter to create a bubbling sound. The higher the fall, the higher the sound it produces. Above all these, the location will also depend on your preference.

Step 3: Get stones-
Various stones with different shapes will be the key to add beauty to the stream. Seek around and ask for the prices. Select a colorful, flat and oddly shaped stones both in small and big sizes. Do the same for gravel but avoid limestone as it encourages algae to grow.

Step 4: Mapping and digging-
Put the stones and boulders around the site. Mark the location of the waterfall and the stream. Likewise, mark the location of upper and lower basins. Use chalk or paint to mark the areas. Dig a hole to place the lower basin. Put stones alongside it. You can use dirt and gravels to keep the stones in place. Dig a hole 2 ft wider than the basin and of 6 ft in depth to place the basin. Prepare the upper pool as the lower one together with the stream tracks.

Step 5: Place the basins-
Starting with the lower basin, drill two holes and attach the adapter to the basin. Cement it firmly. Lay the rubber liner and fabric to the holes. Put the pump and attach the hose. Put the lid and stone layers. Remove sharp objects underneath the basin.

Step 6: Lay liner stones and water-
Lay the fabric from lower to upper basin with slacks at the bottom of each waterfall. Lay decorative stones around the pool. Make sure to put a spillway and small stone around it. Make a staircase and put gravel to invite people and birds. Spay the entire stream area with water. Put water until it rises past the layers of stone in the lower basin. Pump up the water and see it falling. Sit back and enjoy the waterfall.

Author Bio- This article is written by Tressy Jones. She writes about Home Improvement. She works for W A Air Conditioning. They provide best air conditioning services.

Share this with a friend!
Facebook Twitter Pinterest Plusone Linkedin Digg Delicious Reddit Stumbleupon Tumblr Posterous Email

How to Open a Pool after Winter Season

If you want to know how to open a pool then you’ve come to the right place. With spring around the corner we all want to get back to our pools, but we feel unsure about how this should be done. Luckily, we’ve listed a complete routine for you to make sure that the only thing you need to worry about is enjoying the season.

1.     Check chemical levels-
Make sure that you have proper inventory for your pool cleaning ready in your hand. If any of the chemicals were not stored properly or they are in low supply, then you will have to buy replacements. Chlorine for example, if left open over a prolonged period may decay and cause harm to your pool.

2.     Remove debris over the pool cover-
Over the winter dead branches, leaves and debris build up that need to be cleaned up before you remove your pool’s cover. Clean the area around your pool and do the same on the surface of your pool cover, doing this step diligently it will save your lot of time. Finally, remove the pool cover and wash it with a mild detergent to get rid of any bacteria before you move it to storage.

 3.     Inspect your pool-
If your pool is vinyl-lined, you will want to search around the edges for any rips or tears caused by rocks and other debris. If you find any torn parts this can be repaired with a patch kit available at local department store near your house. If there is something that you are unsure of then call the company representative who installed the vinyl for you.

 4.     Plugs & skimmer baskets-
You will want to remove any freeze plugs from water inlets. If you used antifreeze, than drain your pool till it is below the inlets and doing the same for the antifreeze. Next, remove winter plates from the skimmer box with care. Fit the hose from the skimmer and turn jets leading to the pump & filter.

5.     Equipment and plumbing
Reconnect the filter, pump and heater with attention to any rust or decay, if needed make necessary replacements. Check valves to see if they are open and start filling pump with water to test for priming and lubricate O-rings and gaskets.

 6.     Fill & start filtration-
Once everything is in working order, start pumping water into your pool carefully to prevent any debris from falling in. Switch on the power to the pool system and look for any type of malfunctioning, if needed contact a mechanic for repairs.

 7.     Test water
After 1-2 days use your pool water test kit to take a sample for a local pool professional to examine and make necessary adjustments. If you use a mesh cover make sure to add 2-3 gallons of liquid shock and open your pool early in April or May to let the shock treatment to settle in for about 2 weeks.Finally once everything is complete, you and your family can jump in and enjoy a clean and refreshing pool. We hope you found this article helpful on how to open a pool after winter season?

Author Bio- This post has been written by Tressy Jones. She loves to write about Home Improvement. She works for MSMechanical.com. They provide best air conditioning services.

Share this with a friend!
Facebook Twitter Pinterest Plusone Linkedin Digg Delicious Reddit Stumbleupon Tumblr Posterous Email